Schlage Keypad Lock Keeps Spinning

Now, if your Schlage Keypad Lock won’t stop spinning and you’re observing for tips to resolve this problem, this post is your go-to resource. Then, in the following paragraphs, we’ll walk you through some handy tips to troubleshoot this problem. Now, in short, if your Schlage Keypad Lock keeps spinning, replace the batteries.

Schlage Keypad Lock Keeps Spinning

If that doesn’t support it, simply perform a factory reset on the lock and this should resolve the problem.

Tips to Fix a Schlage Keypad Lock that Keeps Spinning:

1. Change the Batteries in Your Lock

Now, if your Schlage Keypad Lock keeps spinning, you need to start your troubleshooting by simply replacing the batteries in the lock. The lock is battery-powered, so it might develop some problems if the batteries are low.

Now, for this issue, the motor of the lock might not have enough power to engage the mushroom pin fully—because the battery power is low.

Your Schlage Keypad lock will blink red reliably when the batteries are low. If you see red flashes on your lock, simply get a new set of batteries and you need to replace the old ones. For Schlage BE365, get a 9V battery and replace the old one.

Though, if you don’t see red flashes on the lock, you should still go ahead and replace the batteries. Sometimes, the batteries in your lock might drain out rapidly without the usual warnings—probably because the batteries are wicked or because of the cold. If your Schlage Keypad keeps spinning after replacing the batteries, just continue to the next step.

2. Restore Default Settings on the Lock

Simply Resetting the lock is another fix to try if your Schlage Keypad Lock keeps spinning and resetting the lock will remove all settings in your lock and restore the default settings. This typically benefits fixing problems produced by improper settings or interior glitches.

Now, before you reset your lock, simply look for the default Programming Code, as you’ll need it to program your lock after the reset. See how to find your Schlage Keypad Lock default Programming Code.

Next, you can simply go ahead with the reset. Here is how you can do that:

• You need to remove the battery cover and disconnect the battery.
• After that, you need to press and release the Schlage button.
• Then, simply reconnect the battery and simply press and hold the Schlage button until you see a green light and the lock beeps. This step should be finished in 10 seconds.

Now, if this method doesn’t reset your lock, simply read more about resetting a Schlage keypad Lock.

3. Reinstall the Lock

Now, if the problem continues after the reset, the lock might have been installed wrongly. Your Schlage Keypad Lock might develop problems, such as spinning, and not locking/unlocking if it’s not installed correctly.

You’ll need to eliminate the lock from the door and install it. You need to get the user manual that came with your lock and simply follow the installation guidelines correctly. If you don’t have the user manual, try googling your Schlage lock model installation directions or get an expert to support you reinstall the lock.

More so, a component in your lock might have been wrecked or shifted from its original position (this is mutual with the Schlage BE365 Keypad Lock).

Now, if you discover that a component in the lock is broken while reinstalling it, simply contact Schlage Customer Support for a replacement. The video below shows how you can fix the spring in your Schlage Keypad Lock and this should support resolving the spinning problem.

FAQs

• Why is my Schlage lock keypad not working?

You need to make sure you didn’t enable Vacation Mode: now, if vacation mode is enabled, the keypad will not work. You simply need to restart or reset your lock: simply try unclipping the batteries and reconnecting them to see if a basic restart helps. Then, simply try a full factory reset on the lock.

• Why is my Schlage electronic lock, not opening?

You need to press the Schlage button once and then simply reconnect the battery: On the keypad, you just need to press and release the Schlage button one time. You simply need to reconnect the battery within 10 seconds of pressing the button.

• What really happens if the Schlage battery dies?

Now, if the battery is dead and you need to unlock the door, you can simply perform an emergency battery jump start. You need to follow these steps to perform an emergency jump start. You just need to connect a new high-quality alkaline 9-volt battery to the contacts below the touchscreen and just listen for a long beep.

Also Check:

• How to Lock Smonet Smart Lock From Outside
• WeLearn 2.0
• Keypad Door Lock Not Working
• How to Add Money to Cash App Card at 7-Eleven

Conclusion:

As we have discussed above, you can simply fix your spinning Schlage Keypad Lock by changing the batteries and resetting the lock. Though, these fixes don’t work all the time and the installation might be wrong if you’ve substituted the batteries and reset the lock, but it just keeps spinning.

You just need to remove the lock from the door and install it back properly and if the problem is not resolved after this, simply contact Schlage Customer Support for support.

You might also need to get a new lock liable on how long you’ve used it and the lock might be too old and have reached the end of its lifespan.

We have shared everything about fixing Schlage Keypad Lock Keeps Spinning in this article for you if the info that we shared above assisted you in any way then do share it with others.